Bills banning foreign ownership of NC farmland advance
Two committees in the North Carolina General Assembly voted Tuesday morning to approve legislation banning certain foreign entities from acquiring farmland in the state.
The House Homeland Security and Military and Veterans Affairs Committee took up House Bill 133, 'NC Farmland and Military Protection Act.' About an hour later, the Senate Agriculture, Energy, and Environment Committee approved the upper chamber's counterpart, Senate Bill 394, 'Prohibit Foreign Ownership of NC Land.'
Both measures now head to subsequent panels — House Commerce and Economic Development and Senate Judiciary, respectively.
At a time of rocky international relations due to the Trump administration's tariffs, the legislation could signify a move toward increased tension with foreign countries.
HB 133, sponsored by Reps. Jennifer Balkcom (R-Henderson), Neal Jackson (R-Moore, Randolph), Jeff Zenger (R-Forsyth), and John Bell (R-Goldsboro), would prohibit 'adversarial' foreign governments from purchasing, acquiring, or leasing agricultural land in North Carolina, according to the bill text.
The restrictions would also apply to land situated within a 75-mile radius of a military installation — a number influenced by national defense recommendations, Balkcom said — such as Fort Bragg near Fayetteville. A complete list of applicable installations is outlined in the bill text.
'If it was up to me, I'd do the entire state,' Balkcom said. 'But this doesn't infringe on private property rights. You can sell it to anybody but a foreign national that's an adversary against the United States.'
Rep. Celeste Cairns (R-Carteret, Craven) asked for clarification on the bill's parameters. She asked if people would be able to sell property to individual citizens of the 'adversarial' countries without connection to their government.
Balkcom responded in the affirmative. In response to a question from Rep. Wyatt Gable (R-Onslow) about how the 'adversarial' governments are defined, she said there's guidance from the U.S. Department of Defense.
Although the bill doesn't list specific countries, it refers to governments subject to the International Traffic in Arms Regulations.
Over in the upper chamber, Sens. Bob Brinson (R-Beaufort, Craven, Lenoir), Bobby Hanig (R-Bertie, Camden, Currituck, Dare, Gates, Hertford, Northampton, Pasquotank, Perquimans, Tyrrell), and Timothy Moffitt (R-Henderson, Polk, Rutherford) serve as the primary sponsors for SB 394.
The measure explicitly refers to the 'adversarial' nations by name: China, Iran, North Korea, and Russia.
Brinson described the legislation as a state effort to protect national security, because 'food security is national security.'
'The key purpose of this bill is to both safeguard our agricultural integrity and to protect our national security,' he said. 'This bill ensures that North Carolina farmland does not come under international adversarial control, and also prevents adversarial nations from acquiring land near sensitive military installations.'
SB 394 is more restrictive than its House counterpart. The proposal bars the prohibited foreign parties from making claims to land situated within a 25-mile radius of a military installation or land underneath special use airspace as designated by the Federal Aviation Administration.
Sen. Lisa Grafstein (D-Wake) pointed out there is a growing population of Chinese immigrants and Chinese Americans in the state. She asked if the bill would ban someone from purchasing land if they are a legal resident of the U.S. with Chinese citizenship.
'If they're a resident alien of the U.S., they have the same right to acquire or hold land as a citizen, as long as they're a resident in the state,' Brinson said. 'As long as they are a legal resident alien, they should have the same land ownership rights as a citizen.'
Hashtags

Try Our AI Features
Explore what Daily8 AI can do for you:
Comments
No comments yet...
Related Articles


Business Wire
3 days ago
- Business Wire
Vitable Health Expands Care-Backed ICHRA Platform to Pennsylvania, Texas, and Florida Amid Rising Demand for SMB Health Benefits
PHILADELPHIA--(BUSINESS WIRE)-- Vitable Health, the leading all-in-one health benefits platform redefining care for the American workforce, today announced the availability of its care-backed ICHRA (Individual Coverage Health Reimbursement Arrangement) services in Pennsylvania, Texas, and Florida. This expansion follows the company's successful launch in Ohio and reflects growing demand from small businesses for health benefits that actually deliver care, not just coverage. As healthcare costs rise and small businesses continue to be left behind by traditional group insurance models, ICHRA adoption is accelerating across the country. New U.S. Census Bureau data, analyzed by BenefitsPro, shows that Florida and Texas are among the states with the highest uninsured rates, underscoring the urgent need for solutions that help employers close coverage gaps. According to the most recent HRA Council report, 83.5% of employers offering an ICHRA or QSEHRA did not provide any health benefits prior—a sign of the model's potential to expand access where it's needed most. 'Legislation will always lag behind reality,' said Joseph Kitonga, CEO of Vitable Health. 'This expansion is about more than geography, it's about proving that small businesses don't need to wait for lawmakers to fix the system. Affordable, high-quality healthcare for the working class isn't theoretical. It's here, it's working, and it's only the beginning.' In many of these markets, small businesses are facing what Vitable Health calls 'coverage deserts,' where traditional plans have become cost-prohibitive or inaccessible. By combining ICHRA administration with unlimited virtual primary care, preventive screenings, diagnostic lab panels, and zero-dollar prescriptions, Vitable removes the friction that typically keeps benefits and care siloed. This integrated model simplifies compliance for employers while improving health access and engagement for employees, particularly in industries like home health, construction, and hospitality, where coverage has historically been out of reach. In Pennsylvania, where Vitable Health is headquartered, this expansion marks the next stage of growth in the company's largest and most mature market. In Texas and Florida, two of the country's most challenging benefits environments, Vitable Health is helping employers deliver a competitive edge by pairing cost-efficient ICHRA benefits with real care. 'With Ohio's HB 133 and Indiana's HB 1004 setting the tone and ICHRA bills surfacing in other states, the message is clear: change is coming,' Kitonga added. 'The employers who act now aren't just getting ahead of the curve—they're leading it.' With this multi-state expansion, Vitable Health is demonstrating what a new standard for small-business health benefits looks like: affordable, accessible, and centered on real care rather than bureaucracy. To learn more about Vitable Health's ICHRA and primary care offerings for small businesses, visit Vitable Health is the nation's leading health benefits platform, making healthcare better for business owners and employees. With a focus on real access over red tape, Vitable Health offers employers affordable, ACA-compliant health benefit solutions, including Minimum Essential Coverage (MEC) plans, MVP plans, and ICHRA and QSEHRA options, that are packaged with Direct Primary Care and can be enhanced with Vision and Dental benefits. Every plan includes access to virtual primary care visits, mental health coaching, and over 1,000 covered prescriptions and labs with zero out-of-pocket costs. To date, Vitable Health has raised $25 million from top-tier investors, including First Round Capital, Y Combinator, Cherryrock Capital, Citi Bank's Impact Fund, Commerce Ventures, Jack Altman, Michael Seibel, Immad Akhund, and SoftBank Opportunity Fund.

Epoch Times
30-07-2025
- Epoch Times
North Carolina General Assembly Overrides Governor's Vetos to Pass Laws
The North Carolina General Assembly, the state's legislature, voted to override several vetoes issued by Gov. Josh Stein, allowing the bills to become law. Although Stein, a Democrat, won by a 14-point margin in the 2024 election, the General Assembly's makeup remained largely unchanged, with Republicans retaining a three-fifths majority in both the Senate and House.


Time Business News
18-07-2025
- Time Business News
Navigating ITAR and RoHS Compliance in PCB Assembly
PCB assemblies are the backbone of modern electronics, powering everything from smartphones to satellites. Yet, behind every successful circuit board assembly lies a complex web of regulations that manufacturers must navigate to ensure both legal operation and market access. In the United States, two of the most critical compliance pillars for turnkey PCB assembly are ITAR (International Traffic in Arms Regulations) and RoHS (Restriction of Hazardous Substances). For PCB assembly providers in the USA, meeting these standards is not just a box-ticking exercise—it is a fundamental requirement for participating in defense, aerospace, and global electronics markets. Compliance impacts every stage of the process, from material sourcing to final shipment. This blog unpacks what ITAR and RoHS mean for circuit board assembly, highlights their key differences, outlines best practices, and addresses common challenges faced by U.S.-based manufacturers. ITAR stands for International Traffic in Arms Regulations, a set of U.S. government rules that control the export and import of defense-related articles and services. The U.S. Department of State, specifically the Directorate of Defense Trade Controls (DDTC), administers ITAR. Its primary goal is to prevent sensitive military technologies from falling into the wrong hands, safeguarding national security. PCB assemblies designed for military, aerospace, and defense applications are often classified as ITAR-controlled. This includes, but is not limited to: Satellite boards Guidance systems RF (radio frequency) modules Any circuit board assembly that is specifically designed for use in defense articles listed on the United States Munitions List (USML) is subject to ITAR. Even technical data, such as fabrication drawings and netlists, can be ITAR-controlled. Registration: Companies must register with the DDTC before engaging in ITAR-related manufacturing or export activities. Companies must register with the DDTC before engaging in ITAR-related manufacturing or export activities. Documentation: Detailed records of all transactions, technical data transfers, and physical movements of ITAR-controlled items must be maintained for audit purposes. Detailed records of all transactions, technical data transfers, and physical movements of ITAR-controlled items must be maintained for audit purposes. Secure Data Handling: Only U.S. persons may access ITAR-controlled data, and secure IT systems are required to prevent unauthorized access. Only U.S. persons may access ITAR-controlled data, and secure IT systems are required to prevent unauthorized access. Export Licensing: Manufacturing or exporting ITAR-controlled PCBs often requires obtaining specific licenses from the U.S. government. Manufacturing or exporting ITAR-controlled PCBs often requires obtaining specific licenses from the U.S. government. Facility and Labor Requirements: Facilities may need export-restricted zones, and all involved personnel must be U.S. persons. This impacts hiring, training, and facility access policies. RoHS stands for Restriction of Hazardous Substances. Originating as an EU directive, RoHS restricts the use of ten hazardous materials—including lead, cadmium, mercury, and certain phthalates—in electrical and electronic equipment. The aim is to reduce environmental impact and health risks associated with electronic waste. Lead-Free Soldering: PCB assembly lines must use lead-free solder alloys, such as tin-silver-copper, and avoid fluxes containing restricted substances. PCB assembly lines must use lead-free solder alloys, such as tin-silver-copper, and avoid fluxes containing restricted substances. Material Selection: All base materials, finishes (e.g., ENIG), and components must be RoHS-compliant. Suppliers must provide documentation confirming this compliance. All base materials, finishes (e.g., ENIG), and components must be RoHS-compliant. Suppliers must provide documentation confirming this compliance. Labelling and Testing: Each shipment of RoHS-compliant circuit boards should include a Certificate of Conformance and clear labelling. X-ray fluorescence (XRF) analyzers may be used to verify the absence of restricted substances. Each shipment of RoHS-compliant circuit boards should include a Certificate of Conformance and clear labelling. X-ray fluorescence (XRF) analyzers may be used to verify the absence of restricted substances. Vendor Compliance: Manufacturers must ensure that all components and materials sourced are RoHS-compliant, often requiring supplier audits and documentation checks. Although RoHS began as an EU regulation, it has been adopted in various forms worldwide. In the U.S., states like California have implemented their own RoHS laws, and the Waste Electrical and Electronic Equipment (WEEE) directive also influences domestic practices. U.S. manufacturers follow RoHS to access international markets and meet global customer expectations. Aspect ITAR RoHS Scope National security, defense, military Environmental health and safety Applicability Military, aerospace, defense sectors Consumer, industrial, all electronics Enforcement U.S. Department of State (DDTC) EU authorities, U.S. state agencies Penalties Severe fines, export bans, prosecution Fines, product recalls, market bans Overlap Possible for military boards exported abroad—may require both ITAR and RoHS compliance (e.g., lead-free military PCB) ITAR: Registration with DDTC, restricted access zones, and secure data systems are mandatory for ITAR-sensitive work. RoHS: Dedicated lead-free manufacturing lines, compliant soldering processes, and regular equipment audits are essential. RoHS: Material declarations, Certificates of Conformance, and batch-level traceability records must be maintained. ITAR: Controlled technical data, access logs, and export documentation are required for every transaction and transfer. ERP/MRP systems help track materials, manage documentation, and ensure traceability for both ITAR and RoHS requirements. Automated reporting aids in conflict mineral tracking and regulatory audits. Always verify a supplier's ITAR registration and RoHS certification. For ITAR-sensitive projects, selecting a U.S.-based turnkey PCB assembly provider is critical to avoid unauthorized foreign access and ensure full regulatory compliance. A U.S. defense contractor requires an RF module for a missile guidance system. Using an offshore supplier could risk unauthorized access to ITAR-controlled designs, resulting in severe penalties. The workflow involves design, secure data transfer, U.S.-person-only assembly, and detailed documentation from design to delivery—all within a registered, secure U.S. facility. A consumer electronics OEM sources components from multiple vendors. To achieve RoHS compliance, the procurement team conducts supplier audits, collects Certificates of Conformance, and ensures lead-free soldering during assembly. Regular testing and documentation are maintained to satisfy EU market requirements. Using Non-Compliant Components: Always verify supplier certifications and test materials if necessary. Always verify supplier certifications and test materials if necessary. Exporting ITAR-Controlled Designs Without Licenses: Never share technical data or products internationally without proper DDTC licensing. Never share technical data or products internationally without proper DDTC licensing. Failing to Document RoHS Conformity: Maintain up-to-date records and Certificates of Conformance for all shipments. Maintain up-to-date records and Certificates of Conformance for all shipments. Relying on Unverified Vendors: Work only with certified, U.S.-based partners for ITAR-sensitive projects and demand RoHS documentation from all suppliers. Integrate Compliance Early: Address ITAR and RoHS requirements during the design phase (DFX approach) to avoid costly redesigns or delays. Address ITAR and RoHS requirements during the design phase (DFX approach) to avoid costly redesigns or delays. Maintain a Vetted Supplier List: Regularly audit and update approved vendors to ensure ongoing compliance. Regularly audit and update approved vendors to ensure ongoing compliance. Train Teams on Regulations: Provide ongoing training for engineering, procurement, and quality teams on evolving ITAR and RoHS rules. Provide ongoing training for engineering, procurement, and quality teams on evolving ITAR and RoHS rules. Monitor Legislative Updates: Stay informed about changes, such as ITAR amendments or RoHS 3 updates, to remain compliant and competitive. Navigating ITAR and RoHS compliance in PCB assembly is not just about avoiding penalties—it is about ensuring access to critical markets, protecting sensitive technologies, and supporting environmental responsibility. For OEMs and manufacturers, working with certified, experienced domestic partners like Star Engineering provides peace of mind and a distinct competitive advantage. Star Engineering offers turnkey PCB assembly solutions that meet the highest standards of ITAR and RoHS compliance. Connect with the Star Engineering team today to ensure every circuit board assembly meets the requirements for quality, security, and global market access. TIME BUSINESS NEWS